Course Assessment - Structural Boundary Conditions
Quiz Summary
0 of 10 Questions completed
Questions:
Information
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You must first complete the following:
Results
Results
0 of 10 Questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 point(s), (0)
Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)
Categories
- Not categorized 0%
-
Unfortunately, you did not pass the quiz.
Don't be discouraged - Go through the course material including the lecture videos, handout slides, and simulation examples to prepare and try again.
-
Congratulations, you have passed the quiz!
You still have room for improvement - Review the slides and simulation examples again to identify the concepts that you may have missed.
-
Congratulations, you have passed the quiz!
You scored better than average, but if you are still unsure about a particular topic, try starting a discussion on the Ansys Learning Forum to discuss your questions with peers around the world.
-
Congratulations, you have passed the quiz!
You did great - Check out other courses to further your knowledge. Also, visit the Ansys Learning Forum and participate in discussions on this subject to help your peers and deepen your own knowledge.
-
Congratulations you have passed the quiz!
You have excelled on this topic - Check out other courses and see if you can ace them too. Also, visit the Ansys Learning Forum to help your peers on this topic. With your knowledge, you can make a real difference.
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- Current
- Review
- Answered
- Correct
- Incorrect
-
Question 1 of 10
1. Question
In a Linear Stress Analysis, changing which of the following input parameters does NOT always result in a linear variation of the output, such as calculated deformation? Select the best option.
CorrectIncorrect -
Question 2 of 10
2. Question
Consider the 1D case of two connected bar elements that have a total of three nodes i, j and k. Node j is shared by the two bar elements, and no boundary conditions are applied. If we solve the finite element equation in a static analysis, which of the following statements are TRUE? Select the two correct options.
CorrectIncorrect -
Question 3 of 10
3. Question
What is the cause of a "DOF LIMIT EXCEEDED" error? Select the two correct options.
CorrectIncorrect -
Question 4 of 10
4. Question
Which of the following statements hold TRUE for the nodes of line and surface bodies which lie on a Symmetry Region? Select the two correct options.
CorrectIncorrect -
Question 5 of 10
5. Question
Consider the case where a Pressure load of 100 MPa is scoped to two surfaces, Surfaces A and B. Surface A has an area of 20 mm2, and Surface B has an area of 60 mm2. How is the pressure load distributed to the two surfaces? Select the best option.
CorrectIncorrect -
Question 6 of 10
6. Question
Let us consider a simple case of a slender cantilever beam. It is fixed at one end, and on the other end, we have a small face on which to apply a bending load. Which of the following statements holds true if we consider large deflection effects? Select the two correct options.
CorrectIncorrect -
Question 7 of 10
7. Question
In Ansys Mechanical, Standard Earth Gravity and Acceleration are essentially the same types of load except for which of the following reasons? Select the two correct options.
CorrectIncorrect -
Question 8 of 10
8. Question
Which of the following is true for Rotational Velocity? Select the two correct options.
CorrectIncorrect -
Question 9 of 10
9. Question
Thermal stress is developed under certain conditions. Select the three correct options that cause thermal stresses.
CorrectIncorrect -
Question 10 of 10
10. Question
Which of the following statements are TRUE regarding thermal and structural analyses performed in Ansys Mechanical? Select the two correct options.
CorrectIncorrect